China
Africa
Explore chapters and articles related to this topic
LED Control with Different Evaluation Boards (Arduino Uno and NodeMCU)
Published in Anudeep Juluru, Shriram K. Vasudevan, T. S. Murugesh, fied!, 2023
Anudeep Juluru, Shriram K. Vasudevan, T. S. Murugesh
Jumper wires are specialized electrical wires with connectors or pins at each end. These are used for interconnection between breadboards, evaluation boards, sensors, modules or any other electronic devices and are available in various combinations as shown in Figure 1.13: Male to Male Jumper Wires – shortly called as M2M Jumper wires. These jumper wires have pins at both ends.Male to Female Jumper Wires (or Female to Male Jumper Wires) – shortly called as M2F Jumper wires. These jumper wires have pins at one end and a connector at the other end.Female to Female Jumper Wires – shortly called as F2F Jumper wires. These jumper wires have connectors at both ends.
J
Published in Philip A. Laplante, Comprehensive Dictionary of Electrical Engineering, 2018
^ where for each (t) = i matrices K (i) are the unique positive semidefinite solutions of algebraic coupled Riccati equations. This solution may be also found as the steady-state value of K (i, t). See also linear system with Markov jumps. jumper a plug or wire used for setting the configuration of system. It can be used for changing the hardware configuration by forcing some line to be high or low. It is used to change software configuration (especially on embedded systems) when the status of the jumper is read by the microprocessor. jumping jack a voltmeter.
J
Published in Phillip A. Laplante, Dictionary of Computer Science, Engineering, and Technology, 2017
jumper a plug or wire used for setting the configuration of system. It can be used for changing the hardware configuration by forcing some line to be high or low. It is used to change software configuration (especially on embedded systems) when the status of the jumper is read by the microprocessor.
Performance analysis of shapeable-maximum power point tracking technique from thermoelectric-solar hybrid energy harvesting sources on mobile devices
Published in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 2021
Azdiana Md Yusop, Ramizi Mohamed, Noor Asyikin Sulaiman, Ahmad Sadhiqin Mohd Isira
The findings from analysis carried out for system 1 using supercapacitor 5 F indicate that the charging occurs for 15 s for discontinuous sources and 13 s for continuous sources at the initial time of the experiment. The next condition is the condition where on-off charging occurs simultaneously. This condition causes the charging process to almost not occur and since this condition persists, at the time of 340 s the supply is disconnected from the system to avoid any damage to the load and it is found that the voltage on the second MPPT board is static again at 5 V. The significant difference for continuous and discontinuous supply modes is when the load is disconnected, the plot of the graph of the supercapacitor voltage becomes static at the final value before the load is disconnected. However, in continuous mode of supply, the voltage value increases back to 1.8 V which is the voltage value of the first MPPT board that has been restricted first through JP1 jumper. Hence the same analysis is carried out for the 10 F supercapacitor and the output voltage behavior for each test point can be seen in Figure 6.
Dual arm electrical transmission line robot: motion through straight and jumper cable
Published in Automatika, 2019
C. M. Shruthi, A. P. Sudheer, M. L. Joy
An appropriate robot mechanism for both tension and suspension towers are not reported till now for transmission line inspection. Most of the existing line inspection robots are heavy, bulky with several complicated mechanisms and are costly. Most of the existing robots fails to cross tension towers due to the absence of appropriate mechanisms to cross jumper cables. It is also observed that the robots were not autonomous and needed manual operator to supervise the inspection operation. Moving through straight line and crossing through jumper cable are the main challenges in the development of the mechanism for high voltage line inspection.
Highly sensitive gold-film surface plasmon resonance (SPR) sensor employing germanium selenide (GeSe) nanosheets
Published in Instrumentation Science & Technology, 2022
Ze-Ying Hao, Yao Liu, Zhou-Hao Zhao, Qi Wang
The constructed sensor was submerged in glycerol solutions with refractive indices from 1.3340 to 1.3622 in order to determine its sensitivity. By connecting the sensor’s two ends via jumper cables to a computer and a spectrometer, real-time signal detection was achieved. Using the computer’s display, the sensor’s transmission spectra were plotted, and the sensor sensitivity was calculated from the spectra. Figure 4 shows a schematic representation of the measurement system.